Peptide reconstitution calculator

Select your peptide, syringe size, and dose — see draw units update instantly.

Configure

mg
1 mg100 mg
mL
0.5 mL10 mL
mcg
10 mcg5000 mcg

Your dose

Draw to

—

units

Select values to calculate

How to use your syringe

Pull the plunger until the liquid reaches the blue line — that matches the unit mark on a real U-100 insulin syringe.

Syringe draw level diagram Shows how far to pull the plunger for your calculated dose. NEEDLE DRAW HERE unit mark 100 units 0 units units →
  1. 1
    Pick the same syringe size

    Use a 1.0 mL (100 unit) U-100 syringe — the scale on the barrel should read 0–100.

  2. 2
    Draw peptide from the vial

    Insert the needle, turn the vial upside down, and pull the plunger slowly until the liquid column hits the blue line.

  3. 3
    Match the marking on the barrel

    Align the top of the liquid (or plunger seal) with the — mark on the syringe scale.

Select a dose above to see your draw level.

—mcg/mL
—doses / vial
—volume

How to reconstitute

1

Add BAC water

Aim against the vial wall — never spray directly onto the lyophilized cake.

2

Gently dissolve

Swirl or roll between palms. Do not shake — foaming can damage peptides.

3

Draw your dose

Follow the syringe diagram — pull to the blue line and match that unit number on your barrel.

BAC water mixing guide

1

Wash hands & sanitize

Wash hands thoroughly with soap. Wipe the vial rubber stopper and your work surface with an alcohol swab. Let air-dry.

2

Draw BAC water

Use a fresh syringe to draw the amount shown in the calculator above (e.g. 2 mL). Pull the plunger slowly to avoid air bubbles.

3

Inject into the vial

Push the needle through the rubber stopper at an angle. Slowly let the water run down the glass wall — do not blast the powder directly.

4

Let it dissolve

Keep the vial upright and gently roll between your palms for 30–60 seconds. Do not shake. Wait until the liquid is clear with no visible flakes.

5

Store correctly

Reconstituted peptides should be kept refrigerated (2–8 °C) and used within the storage window for that peptide. Label the vial with the date.

Subcutaneous injection guide

1

Prepare supplies

Reconstituted vial, a fresh U-100 insulin syringe, two alcohol swabs, and a sharps container. Wash hands again before proceeding.

2

Pick an injection site

Subcutaneous fat on the lower abdomen (2 inches from the navel), outer thigh, or upper arm. Rotate sites each time to avoid tissue buildup.

3

Draw the dose

Wipe the vial stopper. Insert the needle, turn the vial upside down, and pull the plunger to the blue-line unit mark shown in the calculator.

4

Clean the site & inject

Wipe the injection site with alcohol and let it dry. Pinch a fold of skin, insert the needle at a 45° angle, push the plunger slowly and steadily.

5

Withdraw & dispose

Pull the needle out, press the site with a clean swab (do not rub). Place the used syringe directly into a sharps container — never recap by hand.

Calculator FAQ

What do syringe “units” mean?

On U-100 insulin syringes, 100 units = 1 mL. A 0.3 mL barrel shows 0–30 units; 1.0 mL shows 0–100 units.

Does more water change my dose?

No — the total peptide in the vial is fixed. More water lowers concentration so you draw a larger volume for the same mcg dose.

Which syringe should I use?

For draws under ~15 units (0.15 mL), a 0.3 mL syringe gives finer tick marks. This tool warns if your dose exceeds the selected barrel capacity.

Need product codes or batch COAs?

Browse our catalog and COA library on this site.

Open catalog